Scubapro MK11 Evo/C370 Regulator System 1st and 2nd Stage Set

Follow the interval in your regulator's manual, since manufacturers commonly specify an annual inspection or a set number of dives and many warranties depend on it. A regulator is life-support equipment, so service belongs with a factory-trained technician rather than being attempted at home. Have it looked at sooner than scheduled if you notice increased breathing effort, free-flow, bubbles, or water in the second stage.

Make sure the dust cap is dry and firmly seated over the first-stage inlet before the regulator goes anywhere near water, because water inside the first stage is the leading cause of internal corrosion. Rinse in fresh water without pressing the purge button, since purging while depressurized can draw water back into the second stage. Shake out the water and hang it to dry with the hoses in wide, gentle loops rather than tight bends.

Regulators travel well and are usually best carried in hand luggage where they will not be crushed or lost. A regulator holds no gas of its own, so there is nothing inherently problematic about it on an aircraft, though the airline and security screeners always have the final say. Pack it dry with the dust cap in place, in a padded regulator bag or wrapped in soft gear.

Many modern regulators are supplied as suitable for nitrox mixes up to 40 percent oxygen, which is the widely used recreational industry standard, while anything above that requires dedicated oxygen-clean equipment and procedures. Confirm what your specific regulator's manual states, and follow your nitrox training and your fill station's requirements. Never assume a regulator is oxygen-service clean simply because it looks clean or is new.

A yoke (A-clamp) fitting clamps over the tank valve and is the most common connection across much of the recreational world, while a DIN fitting screws into the valve and is standard in much of Europe and in technical diving. DIN captures the o-ring inside the threads, which many divers consider more secure, but yoke is often what rental cylinders provide. Adapters exist in both directions, so check what is used where you dive before deciding.

The octopus is your backup second stage, carried so you can share air with a buddy who is out of gas, or breathe from it yourself if your primary fails or free-flows. It is normally on a longer, brightly colored hose so it is easy to find and hand over under stress. Secure it in the triangle between your chin and the bottom of your rib cage so it is instantly accessible and not dragging through sand or coral.

Store it fully dry, out of sunlight, with the dust cap in place and the hoses in wide loops rather than tightly coiled. Avoid hanging it by the second stages for long periods, which stresses the hose fittings; laying it flat in a padded bag or hanging it by the first stage is kinder. If it has sat unused for a long stretch, have it checked before your next trip rather than assuming it is ready to dive.

Yes. The MK11 EVO/C370 is CE certified to EN250A European Standards, the cold water category. The first stage uses a sealed balanced diaphragm design with metal thermal fins on a chrome-plated brass body to help manage heat transfer, and the C370 second stage has a coaxial dive/pre-dive lever to reduce the chance of free flow at the surface. Always follow your training and local practice for cold water dives.

The MK11 EVO first stage has two high-pressure ports and four high-flow low-pressure ports. The two HP ports are angled at 15 degrees, which makes gauge or air-integrated transmitter hose routing cleaner over your shoulder. The four LP ports give you room for a primary second stage, an octopus, a BCD inflator hose and a drysuit inflator hose. Intermediate pressure is adjustable externally.

Order YOKE (SKU 12.176.000) if you dive with standard A-clamp tank valves, which are common in North America and much of the recreational world. Order DIN 300 (SKU 12.176.300) if your valves are DIN threaded, which is typical in Europe and in technical diving. Both versions use the same MK11 EVO first stage and C370 second stage; only the tank connection differs.

The set includes the MK11 EVO first stage, the C370 second stage, a 75 cm low-pressure hose and a 4 mm Allen key. You will still need an octopus second stage, a submersible pressure gauge or air-integrated transmitter and a BCD inflator hose, since the first stage has two HP and four LP ports available for those additions.