Mares First Stage Regulator 15X
In stock — ships from Irvine, CA
This item is currently on backorder. Order now to reserve yours, and we will ship it as soon as it is back in stock.
Mares First Stage Regulator 15X - Yoke (INT) is backordered and will ship as soon as it is back in stock.
Pickup available at In Store
Usually ready in 2 hours
Payment & Security
Payment methods
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Product Information
The Mares 15X First Stage Regulator is a balanced diaphragm first stage with a sealed internal mechanism, pre-oriented ports, an ACT valve, and a DFC system for performance at any depth. It is built with two high-pressure ports and four low-pressure ports and is offered in yoke (INT) and DIN connections.
Who it is for
This first stage suits divers who need a standard setup that can run a primary second stage, an octopus, a BCD inflator hose, and a drysuit hose from a single first stage, along with a gauge or transmitter on the high-pressure side. The balanced diaphragm design is intended to deliver consistent gas flow regardless of cylinder pressure or depth, and the sealed diaphragm keeps water and contaminants out of the internal mechanism.
Key details
- Technology: Balanced diaphragm first stage
- Pre-oriented ports with an ACT valve for reliability and safety
- DFC system for performance at any depth
- High-pressure ports: 2, 7/16 in UNF, for a gauge and a transmitter
- Low-pressure ports: 4, 3/8 in UNF, for primary, octopus, inflator, and drysuit hoses
- Weight: 772 g / 27.2 oz (INT) or 598 g / 21.1 oz (DIN)
- Regulator connection: DININT, with yoke and DIN configurations available
Compatibility and sizing
The 15X is available in both yoke (INT) and DIN configurations, so confirm which connection matches your cylinder valve before ordering.
DiveCatalog.com is an authorized Mares dealer and has operated as a dive shop in Irvine, California since 2003. Call 888-701-4017 or start a chat if you have questions about port layout, hose routing, or which connection fits your cylinder.
- Balanced diaphragm design delivers consistent gas flow regardless of cylinder pressure or depth.
- Sealed diaphragm keeps water and contaminants out of the internal mechanism.
- Pre-oriented ports are built into the first stage body.
- ACT valve is included for reliability and safety.
- DFC system is designed for performance at any depth.
- Two high-pressure ports (7/16 in UNF) accommodate a gauge and a transmitter.
- Four low-pressure ports (3/8 in UNF) accommodate primary, octopus, inflator, and drysuit hoses.
- Available in yoke and DIN configurations to match different cylinder valves.
| Brand | Mares |
| Model | 15X |
| Product Type | First stage |
| Technology | Balanced diaphragm |
| Regulator Connection | DININT (yoke and DIN configurations available) |
| HP Ports | 2 (7/16 in UNF) |
| LP Ports | 4 (3/8 in UNF) |
| Weight | 772 g / 27.2 oz (INT); 598 g / 21.1 oz (DIN) |
⚠️ WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.
Frequently Asked Questions
How often does a scuba regulator need servicing?
Follow the interval in your regulator's manual, since manufacturers commonly specify an annual inspection or a set number of dives and many warranties depend on it. A regulator is life-support equipment, so service belongs with a factory-trained technician rather than being attempted at home. Have it looked at sooner than scheduled if you notice increased breathing effort, free-flow, bubbles, or water in the second stage.
How do I rinse and care for a regulator after diving?
Make sure the dust cap is dry and firmly seated over the first-stage inlet before the regulator goes anywhere near water, because water inside the first stage is the leading cause of internal corrosion. Rinse in fresh water without pressing the purge button, since purging while depressurized can draw water back into the second stage. Shake out the water and hang it to dry with the hoses in wide, gentle loops rather than tight bends.
Can I fly with a scuba regulator?
Regulators travel well and are usually best carried in hand luggage where they will not be crushed or lost. A regulator holds no gas of its own, so there is nothing inherently problematic about it on an aircraft, though the airline and security screeners always have the final say. Pack it dry with the dust cap in place, in a padded regulator bag or wrapped in soft gear.
Can I use my regulator with nitrox?
Many modern regulators are supplied as suitable for nitrox mixes up to 40 percent oxygen, which is the widely used recreational industry standard, while anything above that requires dedicated oxygen-clean equipment and procedures. Confirm what your specific regulator's manual states, and follow your nitrox training and your fill station's requirements. Never assume a regulator is oxygen-service clean simply because it looks clean or is new.
What is the difference between DIN and yoke regulators?
A yoke (A-clamp) fitting clamps over the tank valve and is the most common connection across much of the recreational world, while a DIN fitting screws into the valve and is standard in much of Europe and in technical diving. DIN captures the o-ring inside the threads, which many divers consider more secure, but yoke is often what rental cylinders provide. Adapters exist in both directions, so check what is used where you dive before deciding.
What is the octopus regulator for?
The octopus is your backup second stage, carried so you can share air with a buddy who is out of gas, or breathe from it yourself if your primary fails or free-flows. It is normally on a longer, brightly colored hose so it is easy to find and hand over under stress. Secure it in the triangle between your chin and the bottom of your rib cage so it is instantly accessible and not dragging through sand or coral.
How should I store a regulator between dive trips?
Store it fully dry, out of sunlight, with the dust cap in place and the hoses in wide loops rather than tightly coiled. Avoid hanging it by the second stages for long periods, which stresses the hose fittings; laying it flat in a padded bag or hanging it by the first stage is kinder. If it has sat unused for a long stretch, have it checked before your next trip rather than assuming it is ready to dive.
What is the weight difference between the Mares 15X DIN and INT versions?
The DIN version weighs 598 g (21.1 oz), while the INT (yoke) version weighs 772 g (27.2 oz). The DIN version weighs 598 g (21.1 oz) and the INT (yoke) version weighs 772 g (27.2 oz).
How many ports does the Mares 15X first stage have?
The 15X has two high-pressure ports, sized 7/16 in UNF, for a gauge and a transmitter, plus four low-pressure ports, sized 3/8 in UNF, for a primary second stage, an octopus, a BCD inflator hose, and a drysuit hose.
Can I run a drysuit hose off the Mares 15X?
Yes. The 15X has four low-pressure ports, and one of them is intended for a drysuit inflator hose along with the primary second stage, octopus, and BCD inflator connections.
Is the Mares 15X a balanced or unbalanced first stage?
The Mares 15X uses a balanced diaphragm design, which is intended to deliver consistent gas flow regardless of cylinder pressure or depth. It also has a sealed diaphragm to keep water and contaminants out of the internal mechanism.












