Hollis LP Hose, EN250 Low Pressure Scuba Hose, 3/8 in

Pick accessories — 90% off with your $50+ order

Start $501 pick $1252 picks

DiveCatalog DIN Cap for 1st Stage (Female) for Scuba Diving Tanks - Scuba Essentials
$19.95$2.00

1
DiveCatalog Hose Clamp for Scuba Diving - Scuba Essentials
$17.95$1.80

1
DiveCatalog Neoprene Mask Strap Cover
$17.00$1.70

1
DiveCatalog Silicone Mouthpiece Replacement w/ installation - Scuba Essentials
$14.95$1.50

1
DiveCatalog Rubber Tank Valve Protector for Scuba Diving Tanks - Scuba Essentials
$11.95$1.20

1

90% off applies automatically at checkout on orders of $50+ — or free for signed-in members. Not combinable with discount codes.

Payment & Security

Payment methods

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Product Information

The Hollis LP Hose is an EN250 approved low pressure scuba hose offered in a braided Miflex version or a rubber jacketed version, with 3/8 in threading, corrosion-resistant chrome-plated brass fittings and approval for use with up to 40% oxygen. It is made in Italy and individually tested at the factory, so it is a direct replacement for an alternate air source, inflator or drysuit feed hose.

Who it is for

This hose suits any diver replacing or re-routing a low pressure line: a second stage or alternate air source hose, a BCD power inflator hose, or a drysuit inflation feed. Divers using nitrox blends up to 40% oxygen can run it as part of a standard regulator setup. The Miflex version is lightweight, flexible and kink resistant; choose the Miflex braided jacket or the traditional rubber jacket.

Key details

Threading: 3/8 in low pressure fittings in corrosion-resistant chrome-plated brass.
Construction: multi-layer, braided hose with rubber jacket, abrasion resistant and kink resistant.
Miflex inner liner: polyether-based polyurethane, not PVC.
Approvals: EN250 approved and approved for use with up to 40% oxygen.
Quality control: individually tested at the factory and individually marked with the Miflex logo and date code.
Origin: manufactured in Italy.

Compatibility and sizing

Choose your material first, then your length. Miflex lengths offered here are 22 in / 56 cm, 32 in / 76 cm, 36 in / 92 cm and 40 in / 102 cm. Rubber lengths offered here are 22 in / 56 cm, 30 in / 76 cm, 36 in / 92 cm, 40 in / 101 cm, 60 in / 152 cm and 84 in / 213 cm. All versions use standard 3/8 in low pressure threading, so they thread into the low pressure ports of a standard regulator first stage.

DiveCatalog.com is an authorized Hollis dealer and a real dive shop in Irvine, California since 2003. Call 888-701-4017 or start a chat if you want help picking the right length for your regulator, BCD inflator or drysuit routing.

⚠️ WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.

Frequently Asked Questions

What is the difference between the Miflex and rubber versions of the Hollis LP Hose?

Both are EN250 approved low pressure hoses made in Italy with 3/8 in chrome-plated brass fittings and approval for up to 40% oxygen. The Miflex version uses a braided jacket over a polyether-based polyurethane inner liner, not PVC, and each hose is marked with the Miflex logo and date code. The rubber version uses a rubber jacket.

What lengths does the Hollis LP Hose come in?

The Miflex material option is offered in 22 in / 56 cm, 32 in / 76 cm, 36 in / 92 cm and 40 in / 102 cm. The rubber option is offered in 22 in / 56 cm, 30 in / 76 cm, 36 in / 92 cm, 40 in / 101 cm, 60 in / 152 cm and 84 in / 213 cm. Pick the length that matches your routing, such as an alternate air source, inflator or drysuit feed.

Can I use the Hollis LP Hose with nitrox?

Yes. The Hollis LP Hose is approved for use with up to 40% oxygen, which covers standard recreational nitrox blends such as EAN32 and EAN36. It is also EN250 approved and individually tested at the factory. For blends above 40% oxygen, follow your training agency and equipment manufacturer guidance, since this hose's published approval stops at 40%.

Will this hose fit my regulator first stage?

The Hollis LP Hose uses standard 3/8 in low pressure threading with corrosion-resistant chrome-plated brass fittings, so it threads into the low pressure ports found on standard regulator first stages for a second stage, BCD power inflator or drysuit feed. If you are unsure about your first stage ports or the right length for your setup, call DiveCatalog at 888-701-4017.

86%

(1177)

(114)

(37)

(16)

(31)

Excellent wetsuit but will it crush quickly like other wetsuits?

I purchased a BARE 5mm Reactive wetsuit (open box), which was like new, to replace my 1.5 yr old BARE 5mm Velocity wetsuit which had collapsed to only 2.5mm after 3 diving trips (~100 dives). The Reactive wetsuit is well constructed and very flexible. I had to increase the size of the Reactive suit, as it was smaller than the BARE Velocity suit of the same size. Tremendous customer service by Dive Catalog to exchange the wetsuit for proper size. I hope the Reactive suit does not crush so quickly like my other wetsuits (BARE, Henderson, Pinnacle). Hoping that the new technology in this suit will keep me warm below the thermocline.

Perfectly Built

Best of the many many diver hangers in my life. Easily supports my steel-plated BCD, while still donned with all of my accessories. No cracks, bends, or dents. Has even supported my BCD w/ a steel 100 tank attached (not recommended, for safety purposes, though).

Will continue to use this hanger for the long-term. No brainer.

Go-to Dive Hanger

This is a must-have for every diver. It's the quintessential hanger for all dive gear in one small package.

DiveCatalog's "Quick Dry Multi Accessory Dive Gear Hanger for Boots, Gloves, Hood" is set at a great price for a great product. Versatile enough that I've purchased extra hangers to organize my BMX racing gear.

Must-have for divers and anyone looking to organize their adventurous outdoor activities equipment.

Solid Hanger w/ Tons of Options

Does it's job and then some. The added accessory arms gives you options for a multitude of storage solutions. Solid build, solid pricing, must have for owns of dive gear.

New to this hanger...Now I'm a believer

Used tons of dive hangers, but never an upside down hanger. Game-changer for me. Will now add more of these in the near-future.

With it's swivel head design, it can cram itself into my tight dive locker, while still donning a ton of gear.

DiveCatalog's "Upside Down Drysuit Hanger w/ Regulator and Accessory Hooks" is a great product with solid construction at an affordable price. All of that with Dive Catalog's customer support/satisfaction guarantee.

Brand	Hollis
Product Type	Low pressure hose
Material Options	Miflex braided or Rubber
Construction	Multi-layer braided hose with rubber jacket
Inner Liner (Miflex)	Polyether-based polyurethane, not PVC
Fittings	Corrosion-resistant chrome-plated brass
Threading	3/8 in
Use	Second stage, inflator, or drysuit feed
Approval Standard	EN250
Oxygen Approval	Up to 40% oxygen
Testing	Individually tested at the factory
Marking	Individually marked with Miflex logo and date code
Miflex Lengths Offered	22 in / 56 cm, 32 in / 76 cm, 36 in / 92 cm, 40 in / 102 cm
Rubber Lengths Offered	22 in / 56 cm, 30 in / 76 cm, 36 in / 92 cm, 40 in / 101 cm, 60 in / 152 cm, 84 in / 213 cm
SKU Family (Miflex)	204.2382.0XX.M
SKU Family (Rubber)	204.2382.0XX
Country of Manufacture	Italy

Hollis LP Hose

Pick accessories — 90% off with your $50+ order

Payment & Security

Product Information

Who it is for

Key details

Compatibility and sizing

Frequently Asked Questions

What is the difference between the Miflex and rubber versions of the Hollis LP Hose?

What lengths does the Hollis LP Hose come in?

Can I use the Hollis LP Hose with nitrox?

Will this hose fit my regulator first stage?

Hollis LP Hose

Who it is for

Key details

Compatibility and sizing

Let customers speak for us