UPDATE 3/27/26
Huish Outdoors has received reports of internal components within certain Hollis 200LX second stage regulators separating or fracturing before or after a dive.
Their investigation indicates that some units may exhibit reduced impact resistance, particularly if the second stage is dropped or struck on the adjustable inhalation knob. In these cases, damage to the inlet tube assembly could render the second stage non-functional.
While no incidents have been reported during an active dive, this condition could pose a drowning hazard if it were to occur in use. As a precaution, if you have a 200LX affected by this quality alert, stop use immediately. Separate the second stage(s) from the low-pressure hose included with the regulator set and return it to your local service location.
Hollis is currently producing a more durable inlet valve which will allow a retrofit component and resolve the mentioned issue. We expect these parts to be with our global service network within 4-6 weeks of this notice.
The replacement part necessary for this quality alert is an upgraded stainless steel inlet tube which replaces the original brass version. Below is the part number and description of a “LX Inlet Retrofit Kit” – PN 01.000313. This kit includes the following components:
- 5465 – Poppet Seat x 1
- 2.010 – O-ring x 1
- 5474 – O-ring x 2
- 9805 – Stainless Inlet Chamber x 1
- 2.016 – O-ring x 1
It is of the upmost importance that if you have a regulator affected by this quality alert, that you stop use and have the inlet valve replaced as soon as possible. It is recommended to destroy any of the inlet tubes found within the affected range.
While there have been no reported incidents of this occurring during use, we believe that the possibility exists which poses a drowning hazard. We recommend that dealers as well as end users take all necessary precautions when dealing with life support equipment.
Remedy: If you have in your possession a Hollis 200LX regulator affected by this recall, your regulator will be repaired at no cost. Please contact your local authorized Hollis dealer (DiveCatalog.com) or return the regulator back to the place of purchase. For a list of local authorized Hollis dealers, please visit: https:// www.hollis.com/dealer-locator/.
You can also contact Hollis directly by email at recalls@hollis.com or by phone at 1-888-270-8595 option #2 to speak to a service representative regarding this quality alert.
A safety notice has been issued regarding specific 200LX second stage regulators manufactured by Huish Outdoors under the Hollis brand. This advisory applies to certain units purchased between May 2, 2017, and May 15, 2025 and outlines immediate steps for divers, dealers, and distributors.
Affected Part Numbers
The following regulator configurations are included in this notice:
Serial Number Ranges:
- C37523 – C77735
- S73202 – S84427
- HA00001 – HA14873
- LX001698 – LX009896
Part Number & Description:
- 240.2010.07.M — 200LX + DCX Yoke
- 240.2011.07.M — 200LX + DCX DIN
- 240.2000.LX — 200LX 2nd Stage (Black)
Reason for the Notice
Reports have been received of internal components within some affected second stages separating or fracturing either before or after dives. Investigation findings indicate certain units may have reduced impact resistance, especially if the second stage is dropped or struck on the adjustable inhalation knob.
In these cases, damage to the inlet tube assembly could cause the regulator to become non-functional. Although no incidents have occurred during active dives, such a failure underwater could create a drowning hazard. As a precaution, a Stop Use notice has been issued while a full technical review and corrective solution are finalized.
Required Actions
For End Users
- Stop using the affected regulator immediately.
- Remove it from service.
- Do not attempt repair, modification, or continued use.
For Dealers and Distributors
- Stop selling and shipping affected units.
- Quarantine all existing inventory.
- Do not return products unless specifically instructed.
- Notify customers who may have purchased affected regulators.
Remedy and Next Steps
The manufacturer is currently preparing:
- Replacement components
- A standardized retrofit procedure to be performed by authorized technicians
A follow-up notice will provide:
- Parts availability details
- Dealer repair instructions
- Regional customer support processes
Contact Information
For questions until the follow-up notice is released, inquiries can be directed to:
recalls@hollis.com
Summary
This Stop Use / Stop Sale notice is a precautionary safety measure. Prompt compliance helps ensure diver safety while a permanent corrective solution is finalized. Divers and retailers are strongly encouraged to follow all instructions immediately.
