Scubapro C370 Regulator

Follow the interval in your regulator's manual, since manufacturers commonly specify an annual inspection or a set number of dives and many warranties depend on it. A regulator is life-support equipment, so service belongs with a factory-trained technician rather than being attempted at home. Have it looked at sooner than scheduled if you notice increased breathing effort, free-flow, bubbles, or water in the second stage.

Make sure the dust cap is dry and firmly seated over the first-stage inlet before the regulator goes anywhere near water, because water inside the first stage is the leading cause of internal corrosion. Rinse in fresh water without pressing the purge button, since purging while depressurized can draw water back into the second stage. Shake out the water and hang it to dry with the hoses in wide, gentle loops rather than tight bends.

Regulators travel well and are usually best carried in hand luggage where they will not be crushed or lost. A regulator holds no gas of its own, so there is nothing inherently problematic about it on an aircraft, though the airline and security screeners always have the final say. Pack it dry with the dust cap in place, in a padded regulator bag or wrapped in soft gear.

Many modern regulators are supplied as suitable for nitrox mixes up to 40 percent oxygen, which is the widely used recreational industry standard, while anything above that requires dedicated oxygen-clean equipment and procedures. Confirm what your specific regulator's manual states, and follow your nitrox training and your fill station's requirements. Never assume a regulator is oxygen-service clean simply because it looks clean or is new.

A yoke (A-clamp) fitting clamps over the tank valve and is the most common connection across much of the recreational world, while a DIN fitting screws into the valve and is standard in much of Europe and in technical diving. DIN captures the o-ring inside the threads, which many divers consider more secure, but yoke is often what rental cylinders provide. Adapters exist in both directions, so check what is used where you dive before deciding.

The octopus is your backup second stage, carried so you can share air with a buddy who is out of gas, or breathe from it yourself if your primary fails or free-flows. It is normally on a longer, brightly colored hose so it is easy to find and hand over under stress. Secure it in the triangle between your chin and the bottom of your rib cage so it is instantly accessible and not dragging through sand or coral.

Store it fully dry, out of sunlight, with the dust cap in place and the hoses in wide loops rather than tightly coiled. Avoid hanging it by the second stages for long periods, which stresses the hose fittings; laying it flat in a padded bag or hanging it by the first stage is kinder. If it has sat unused for a long stretch, have it checked before your next trip rather than assuming it is ready to dive.

This listing is the C370 second stage only, base SKU 11.371.000, so it does not include a first stage. Scubapro pairs the C370 with the MK11 EVO, MK11 EVO DIN 300 and MK17 EVO 2 first stages in its complete systems, so it is a natural match if you already own one of those or plan to add one. Call 888-701-4017 if you need help confirming the pairing.

No. Scubapro states that C370 Color Frames are compatible only with the current polymer-frame C370 second stage and are not compatible with earlier C370 models that have a metal frame. On the current version the frame snaps on and off quickly using a flathead screwdriver or small pry tool.

Yes. The C370 is CE certified to EN250A European standards for all diving conditions, including extreme cold water. Its air-balanced valve keeps inhalation effort consistent as depth and tank pressure change, and the adjustable inhalation knob plus coaxial dive/pre-dive lever let you tune breathing feel and reduce the chance of a free flow in cold conditions.

Six colors are offered: Gray, White, Blue, Yellow, Turquoise and Pink; the non-gray options pair the second stage with a snap-on Color Frame. The non-gray variants pair the 11.371.000 second stage with a matching snap-on Color Frame made of impact-resistant polymer measuring 2.34 in L x 2.3 in W x 0.45 in H, so you can restyle the second stage later if you wish.