Atomic Aquatics M1 Regulator

Follow the interval in your regulator's manual, since manufacturers commonly specify an annual inspection or a set number of dives and many warranties depend on it. A regulator is life-support equipment, so service belongs with a factory-trained technician rather than being attempted at home. Have it looked at sooner than scheduled if you notice increased breathing effort, free-flow, bubbles, or water in the second stage.

Make sure the dust cap is dry and firmly seated over the first-stage inlet before the regulator goes anywhere near water, because water inside the first stage is the leading cause of internal corrosion. Rinse in fresh water without pressing the purge button, since purging while depressurized can draw water back into the second stage. Shake out the water and hang it to dry with the hoses in wide, gentle loops rather than tight bends.

Regulators travel well and are usually best carried in hand luggage where they will not be crushed or lost. A regulator holds no gas of its own, so there is nothing inherently problematic about it on an aircraft, though the airline and security screeners always have the final say. Pack it dry with the dust cap in place, in a padded regulator bag or wrapped in soft gear.

Many modern regulators are supplied as suitable for nitrox mixes up to 40 percent oxygen, which is the widely used recreational industry standard, while anything above that requires dedicated oxygen-clean equipment and procedures. Confirm what your specific regulator's manual states, and follow your nitrox training and your fill station's requirements. Never assume a regulator is oxygen-service clean simply because it looks clean or is new.

A yoke (A-clamp) fitting clamps over the tank valve and is the most common connection across much of the recreational world, while a DIN fitting screws into the valve and is standard in much of Europe and in technical diving. DIN captures the o-ring inside the threads, which many divers consider more secure, but yoke is often what rental cylinders provide. Adapters exist in both directions, so check what is used where you dive before deciding.

The octopus is your backup second stage, carried so you can share air with a buddy who is out of gas, or breathe from it yourself if your primary fails or free-flows. It is normally on a longer, brightly colored hose so it is easy to find and hand over under stress. Secure it in the triangle between your chin and the bottom of your rib cage so it is instantly accessible and not dragging through sand or coral.

Store it fully dry, out of sunlight, with the dust cap in place and the hoses in wide loops rather than tightly coiled. Avoid hanging it by the second stages for long periods, which stresses the hose fittings; laying it flat in a padded bag or hanging it by the first stage is kinder. If it has sat unused for a long stretch, have it checked before your next trip rather than assuming it is ready to dive.

The Atomic M1 is designed for cold and rough conditions through several features. Its second stage has a thermal heat sink, a super-dry exhaust valve, and a wide deflector, while the first stage is factory-sealed to keep contaminants out. Atomic positions it for specialty diving, whether recreational or technical.

Yes, the Atomic M1 first stage is factory-sealed. It is built from chrome-plated brass with Monel key internals chosen for their strength, corrosion resistance, and oxygen compatibility.

Yes, the Atomic M1 comes factory ready for Nitrox up to 50%, and up to 80% oxygen when following special guidelines. This makes it suitable for both recreational Nitrox diving and more advanced applications.

The Atomic M1 has a service interval of 2 years or 300 dives, whichever comes first. Its lifetime warranty is not contingent on service, and the metal parts carry corrosion coverage for life. Atomic requires purchase from an authorized dealer for warranty coverage, and purchases from us qualify.

The M1 carries a limited lifetime warranty, with metal parts warranted against corrosion for life. All components are covered against material and manufacturing defects for the first 2 years, and consumables like mouthpieces, hoses, o-rings, filters, and valve seats are covered for 2 years. Titanium components are covered for life against corrosion. Warranty registration is required within 30 days of purchase to activate coverage.

The yoke version of the M1 weighs 2.6 pounds combined for the first and second stage. This figure is specific to the yoke-sealed configuration as published by Atomic Aquatics.

The M1 second stage is precision-machined brass with Zirconium plating and Titanium. The M1 also features a stainless steel Seat Saving Dynamic Orifice and a dual silicone comfort mouthpiece with tear-resistant bite tabs.