Aqualung Admiral III Dive Gloves 2mm

As a general rule, thicker neoprene insulates more, so colder water pushes you toward thicker accessories, but fit, dive length, and personal cold tolerance matter as much as the millimeter number. Divers commonly lose a great deal of heat through the head, so a hood is often the highest-value warmth upgrade for the money. Remember that every added piece of neoprene also adds buoyancy you will need to account for.

Boots should fit like a snug athletic shoe, with no heel lift and no crushed toes; a little water inside is normal, a sloshing pocket is not. Try them on with the socks you would actually dive, and remember your fin foot pocket has to accommodate the boot. Hard-sole boots protect on rocky shore entries, while soft-sole boots are lighter and pack smaller for boat and travel diving.

Gloves should be snug across the palm with fingertips reaching the ends without bunching, since trapped air and loose fingertips destroy dexterity. Thicker gloves are warmer but make buckles, clips, and inflator buttons harder to operate, so choose the thinnest glove that keeps you comfortable in your conditions. Try working a clip or buckle while wearing them before you commit.

A hood should seal around the face and neck without restricting your throat or jaw, and lie flat on your head without pulling the mask strap out of position. A loose hood flushes cold water continuously, while an overly tight one is distracting and uncomfortable. Many hoods have a vent to release air trapped during descent, so check yours and burp out any trapped air before you go down.

New neoprene compresses and relaxes with use, so a boot, glove, or hood that feels firm out of the packaging usually settles slightly after a few dives. It should still be snug afterward rather than loose, because neoprene that stretches into a loose fit was probably oversized to begin with. Buy for a snug fit when new, but never for a fit that restricts circulation or breathing.

Yes, because every piece of neoprene you add is buoyancy, and a hood, boots, and thick gloves together can shift your weighting noticeably. Do a proper buoyancy check any time you change your exposure protection rather than assuming your usual weight still works. The weight-check procedure is covered in your training, and a dive professional can help you re-do it.

Rinse them inside and out in fresh water after every dive day, since they hold sweat and salt more than any other gear, and dry them fully inside-out before packing. Dry them out of direct sunlight and never on a heater, because heat hardens neoprene and weakens glued seams. Store them dry and unfolded, as damp neoprene sealed in a bag is how gear picks up a permanent smell.

They are a warm-water glove. The 2 mm neoprene provides moderate warmth and prioritizes dexterity over insulation, so the hand stays close to bare-hand feel for buckles, clips and camera controls. If you dive in genuinely cold water or do long dives where your hands get cold, step up to a thicker glove instead, since 2 mm is aimed at comfort and feel in warm conditions.

Two colorways are offered. Dark Grey/Black, SKU family GL1260112, is available in XS, S, M, L and XL. Twilight/Black, SKU family GL1260501, is available in XS, S, M and L. If the size you need is not shown in the color you want, call or chat with DiveCatalog.com and we can confirm what is available.

The palm is durable Poly-Suede, chosen to hold up through extended use and to grip wet gear. The palm and fingers carry a textured grip surface, which helps when you are handling slick regulators, tanks, lines and camera housings. The rest of the glove combines perforated neoprene, elastic, air-mesh and hook-and-loop fasteners.

Each glove uses an adjustable hook-and-loop wrist strap. Cinching it down seals the cuff and helps prevent flushing, which is the cold water exchange that happens when a loose cuff lets water move in and out as you swim. Because it is adjustable, you can tune the seal to your wrist.