Apeks XTX50 Dive Regulator

Yes — it is one of the classic cold-water regulators. The DST first stage is an over-balanced diaphragm design that is environmentally dry-sealed, keeping water out of the main spring chamber to prevent ice buildup, and the second stage carries a patented heat exchanger around the valve mechanism. Apeks rates the XTX50 for cold-water use, and it delivers gas on a rotating turret with 2 HP and 4 MP ports for clean hose routing.

The second stage is pneumatically balanced with two diver controls: an opening-effort (cracking resistance) knob and an integrated venturi lever that prevents free-flow at the surface. A signature XTX feature: the second stage is reversible for left- or right-hand hose routing (a dealer conversion). Apeks requires service at least once a year by a factory-trained technician, which also maintains the limited lifetime warranty and Free Parts for Life eligibility when purchased from an authorized dealer like us.

Follow the interval in your regulator's manual, since manufacturers commonly specify an annual inspection or a set number of dives and many warranties depend on it. A regulator is life-support equipment, so service belongs with a factory-trained technician rather than being attempted at home. Have it looked at sooner than scheduled if you notice increased breathing effort, free-flow, bubbles, or water in the second stage.

Make sure the dust cap is dry and firmly seated over the first-stage inlet before the regulator goes anywhere near water, because water inside the first stage is the leading cause of internal corrosion. Rinse in fresh water without pressing the purge button, since purging while depressurized can draw water back into the second stage. Shake out the water and hang it to dry with the hoses in wide, gentle loops rather than tight bends.

Regulators travel well and are usually best carried in hand luggage where they will not be crushed or lost. A regulator holds no gas of its own, so there is nothing inherently problematic about it on an aircraft, though the airline and security screeners always have the final say. Pack it dry with the dust cap in place, in a padded regulator bag or wrapped in soft gear.

Many modern regulators are supplied as suitable for nitrox mixes up to 40 percent oxygen, which is the widely used recreational industry standard, while anything above that requires dedicated oxygen-clean equipment and procedures. Confirm what your specific regulator's manual states, and follow your nitrox training and your fill station's requirements. Never assume a regulator is oxygen-service clean simply because it looks clean or is new.

A yoke (A-clamp) fitting clamps over the tank valve and is the most common connection across much of the recreational world, while a DIN fitting screws into the valve and is standard in much of Europe and in technical diving. DIN captures the o-ring inside the threads, which many divers consider more secure, but yoke is often what rental cylinders provide. Adapters exist in both directions, so check what is used where you dive before deciding.

The octopus is your backup second stage, carried so you can share air with a buddy who is out of gas, or breathe from it yourself if your primary fails or free-flows. It is normally on a longer, brightly colored hose so it is easy to find and hand over under stress. Secure it in the triangle between your chin and the bottom of your rib cage so it is instantly accessible and not dragging through sand or coral.

Store it fully dry, out of sunlight, with the dust cap in place and the hoses in wide loops rather than tightly coiled. Avoid hanging it by the second stages for long periods, which stresses the hose fittings; laying it flat in a padded bag or hanging it by the first stage is kinder. If it has sat unused for a long stretch, have it checked before your next trip rather than assuming it is ready to dive.

Both are over-balanced diaphragm first stages built for cold water, and both come with a limited lifetime warranty plus Free Parts for Life when bought from an authorized dealer and serviced annually. The XTX50 is environmentally dry-sealed with a heat exchanger around the second-stage valve, a rotating turret with 2 HP and 4 MP ports, separate cracking-effort and venturi controls, and a second stage that a dealer can reverse for left- or right-hand hose routing. The LEG3ND uses a dry chamber with deep external heat-exchange ribs, adds Aqua Lung's ACD auto closure device, and merges venturi and inhalation adjustment into the single MBS knob. Choose the XTX50 for hose-routing flexibility, the LEG3ND for one-knob simplicity and ACD.

Yoke (INT) is the common fitting on rental tanks in North America and the Caribbean, so it is the easy choice if you mostly dive resorts. DIN screws directly into the valve, is rated for higher pressures and is the standard in Europe and technical diving — and a DIN regulator can use a simple adapter on yoke tanks, which makes it the more flexible option for travelers. Apeks sells the XTX50 in both, so pick based on the tanks you will actually breathe from.

Yes — reversibility is a signature XTX feature: the second stage can be converted for left- or right-hand hose routing, done by a dealer rather than at home. That is what makes it easy to build matched sidemount or stage/deco setups where one regulator has to come over the opposite shoulder. Ask us before you order and we will have it configured the way you dive.